3*6侧面轻触开关 耐高温侧按复位按键卧式音量调节键

品牌	SBR/三博荣	        型号	TS-2845S	        较高电压	12（V）
额定发热电流	50m（A）	用途	汽车设备，安防设备，数码产品，电动玩具，家用设备	   产品认证	ROHS            物料编号	1	        加工定制	是
1. General specification 基本事项
1.1 Switch action :                                          Push-on type S. P. S. T
开关种类 :                                                轻触开关
1.2 Switch rating 较大额定值 :                              D. C. 12V , 50 mA
1.3 Operation temperature range 使用温度试验范围 :            - 20~ + 70oC
1.4 Preservative temperature range 保存温度范围 :              - 40~ + 85oC
1.5 Appearance and dimensions :                              See outside drawing page
外形及尺寸 :                                              见外形尺寸图(XY-TS-100115-7)
1.6 Standard condition Unless otherwise specified, the test and measurements shall be
试验、 测定状态       carried out as follows:
Ambient temperature 温度:                                  5 ~ 35oC
Ｒelative humidity 相对湿度:                                45 ～ 85％
Air pressure 气 压:                                        86 ～ 106kPa(860～1060mbar)
However, if doubt arises on the decision based on the measured Values under the above-mentioned conditions, the following conditions shall be employed:
但是在对判定产生疑义时,按下述状态实施:
Ambient temperature 温 度:                                20±2oC
Relative humidity 相对湿度:                                65±5％
Air pressure 气 压:                                       86 ～ 106kPa(860～1060mbar)
4. Precaution注意事项   4.1 Soldering condition 浸焊条件
ITEM项目	CONDITION条件
Preheat temperature
预热温度	110oC max (Embilomental temperature of soldering surface of P. W. E)
110oC 以下(印刷基板焊锡面周围的温度)
Preheat time
预热时间	60 sec, max
60 秒以内
Area of flux
助焊剂的面积	1/2 max of P. W. B. thickness
印刷基板厚度的1/2 以内
Temperature of solder
焊锡温度	255oC max
255oC 以下
Time of immersion
浸焊时间	Within 5 sec
5 秒以内
Soldering number
浸焊次数	Within 2 times (But should bring down heat of the first soldering)
2 次以内 (但应把**次焊锡的温度降下来)
Printed wiring board
印刷基板	Single sided copper-clad laminates
单面铜箔
(1) After switches were soldered, please be careful not to clean switches with solvent
开关浸焊后,注意不要用溶剂清洗.
(2) In the case of using soldering iron, soldering conditions shall be 280oC max and 3 sec. max
在使用铬铁的情况下,焊锡温度应在280oC 以下、3 秒以内.
(3) Right after switches were soldered; please be careful not to load on the knobs of switches.
浸焊后,注意不要在**部施加负荷.
 2 Design instructions(设计中应注意的事项)
(1) Follow recommended P. W. B. piercing plan in outside drawing page.
印刷基板的安装孔尺寸参见产品图.
(2) Design key top as fig –1. Design inclination of key top 4 deg. max as fig -2.
(Recommended operating condition.)
击键部设计如图 –1,击键部倾斜度如图 –2 在4 度以内. (参见操作条件).
4.3 Note(注意点)
(1) Please be cautious not to give excessive static load or shock to switches.
注意不要施加**负荷的压力或晃动开关.
(2) Please be careful not to pile up P. W. B. after switches were soldered.
开关焊接以后,印刷基板注意不要叠放.
(3) Preservation under high temperature and high humidity or corrosive gas should be avoided
especially. When you need to preserve for a long period, do not open the carton.
保管时尤其应注意避开高湿高温和有腐蚀性气体的环境.如需长时间保存,请不要打开包装箱.
(4) Panasert RH and RH6 shall be used as the standard insert machine (use N type clinch).
使用标准插入机器PANASERT 和RH6（使用N 式钉）
(5) Preservation under high temperature and high humidity or corrosive gas should be avoided especially, when
you need to preserve for a long period, do not open the carton.
特别注意避免将产品保存在高温、强温度或有腐蚀性气体的地方。若长期保存，请勿打开包装箱。